Oct 30, 2020 Leave a message

​The Influencing Factors Of Ultrasonic Metal Welding

The Influencing factors of ultrasonic metal welding

 

Ultrasonic metal welding amplitude


Amplitude is a key parameter for the material to be welded, which is equivalent to the temperature of ferrochrome.

If the temperature is not reached, the welding will not be possible, and if the temperature is too high, the raw material will be scorched or the structure will be damaged and the strength will be deteriorated. The selected ultrasonic transducer is different, the output amplitude of the transducer is different, after adapting the ultrasonic transducer of different transformation ratio


The amplitude and welding head can correct the working amplitude of the welding head to meet the requirements. Usually the output amplitude of the transducer is 10-20μm, and the working amplitude is generally about 30μm. The transformation ratio of the horn and the welding head is related to the shape of the horn and the welding head, the front-to-rear area ratio and other factors.

In terms of shapes, such as exponential amplitude, functional amplitude, stepped amplitude, etc., it has a great influence on the transformation ratio, and the front and rear area ratio is proportional to the total transformation ratio. Choose welding machines of different brands. The easiest way is to make them in proportion to the size of the working welding head to ensure the stability of the amplitude parameters.


Ultrasonic metal welding frequency

Any ultrasonic welding machine has a center frequency, such as 20KHz, 40KHz, etc. The working frequency of the welding machine is mainly determined by the mechanical resonance frequency of the ultrasonic transducer, booster, and horn.


The frequency of the ultrasonic generator is adjusted according to the mechanical resonance frequency to achieve consistency, so that the welding head works in a resonant state, and each part is designed as a half-wavelength resonator. Both the ultrasonic generator and the mechanical resonance frequency have a resonance working range.

Generally set to ±0.5 KHz, the welding machine can basically work normally within this range,


Ultrasonic metal welding node

The nodes, welding heads, and ultrasonic horns are all designed as a half-wavelength resonator of the working frequency. In the working state, the amplitude of the two end faces is the largest and the stress is the smallest, and the node at the middle position has zero amplitude and the largest stress. .


The node position is generally designed as a fixed position, but the thickness of the usual fixed position design is greater than 3mm, or the groove is fixed, so the fixed position is not necessarily zero amplitude, which will cause some calls and some energy loss. Calls are usually isolated from other parts by rubber rings, or shielded by sound insulation materials. Energy loss should be considered when designing the amplitude parameters.


Ultrasonic metal welding transducer

There is no big difference between the transducers for metal welding devices and the transducers for plastic welding devices. The special feature is that the welding metal has higher quality requirements, because a large instant power is often required when welding metal. The transducer is required to have high power capacity and low impedance, without the use of transducers used in plastic welding devices.


Ultrasonic metal welding power supply

There is no big difference between the ultrasonic power supply used in metal welding equipment and the ultrasonic power supply used in plastic welding equipment. The particularity is that welding metal has higher requirements. In order to meet the needs of metal welding, it is necessary to use an intelligent ultrasonic power source-ultrasonic generator.

The ultrasonic generator has an automatic frequency tracking system. Changes in the working conditions of mechanical devices or electronic components during the welding process will cause the vibration frequency to change. The ultrasonic generator will track the frequency of the vibration system, so that the generator and the vibration system are always in In the resonance state, the frequency automatic tracking system can compensate for the changes in the working state that occur during the welding process, so that the system is in the resonance state again and maintains the stability of the welding parameters. The focus is on the stability of the amplitude, which is very important for metal welding.


Ultrasonic metal welding accuracy


Because the ultrasonic welding head works under high-frequency vibration, a symmetrical design should be maintained as much as possible to avoid uneven stress and lateral vibration caused by the asymmetry of sound wave transmission. Unbalanced vibration can cause the welding hair to heat and break. Ultrasonic welding is used in different industries for different processing accuracy requirements. For particularly thin workpieces, such as the welding of lithium ion battery pole pieces and tabs, and the coating of gold foil, the requirements for processing accuracy are very high.


Ultrasonic metal welding life


The service life of a welding head is critically determined by two aspects: first, material, and second, process


Material aspect: Ultrasonic welding requires metal materials to have good flexibility (small mechanical loss during sound wave transmission).

Process: Including the processing technology and subsequent processing technology, the processing technology has been described in detail above, and the subsequent processing includes heat treatment and parameter trimming.

 


Send Inquiry

whatsapp

Phone

E-mail

Inquiry